D1984
forum member
Installed JPC breathers
What have you done to your mustang today?
- Thread starter *JZ*
- Start date
Marble
forum member
I'll be pulling the battery and possibly the alternator. It ran like shit last night at the track and then died on the third pass. Mph was down 5 and then 10 mph, et was off. FML!!!
Nothing like being in front of thousands of people getting the tow of shame back to the pits.
Nothing like being in front of thousands of people getting the tow of shame back to the pits.
Kuplex
Software Developer
Adjusted my MGW again. Changed my oil and refilled my washer fluid.
On the fiancée's Shelby:
Adjusted the linkages on the BMR Watts Link.
Replaced the worn/cracked front stabilizer bushings with the new polyurethane BMR bushings.
Replaced the trans fluid with new custom-blended BND Automotive fluid.
Flushed the brake fluid, got all new Motul RBF600 fluid in it.
Emptied the Billet Tech catch can which was more than half full, quite a bit considering its only been on for about 2,000 miles.
Drove it
Adjusted the linkages on the BMR Watts Link.
Replaced the worn/cracked front stabilizer bushings with the new polyurethane BMR bushings.
Replaced the trans fluid with new custom-blended BND Automotive fluid.
Flushed the brake fluid, got all new Motul RBF600 fluid in it.
Emptied the Billet Tech catch can which was more than half full, quite a bit considering its only been on for about 2,000 miles.
Drove it
travelers
Senior Member
Washed and waxed the car. Looks much better.
Mach2burnout
05 Redfire GT
Ordered these:
for my 69 since I sold my Bullet hole wheels that was on it. Maybe I can get it off jack stands in a week or so.
Sent from iPhone
for my 69 since I sold my Bullet hole wheels that was on it. Maybe I can get it off jack stands in a week or so.
Sent from iPhone
Got a new/used stock driveshaft for it from a buddy with a '12 Roush.
My factory shaft has developed a clunk in the rear section.
I can make it happen if I hold the forward section in place and move the rear section back and forth.
New shaft is noise-free.
Hoping this will eliminate the clunk I get when I first put load on the drivetrain (when I first back up, then if I go forward when I first load the drivetrain in 1st)
My factory shaft has developed a clunk in the rear section.
I can make it happen if I hold the forward section in place and move the rear section back and forth.
New shaft is noise-free.
Hoping this will eliminate the clunk I get when I first put load on the drivetrain (when I first back up, then if I go forward when I first load the drivetrain in 1st)
TexasBlownV8
Formerly TexasBlownV6
Knocked some dead bugs off the cover.
travelers
Senior Member
Ordered these:
for my 69 since I sold my Bullet hole wheels that was on it. Maybe I can get it off jack stands in a week or so.
Sent from iPhone
That's a nice looking wheel
Mach2burnout
05 Redfire GT
Thanks, I did a lot of shopping for wheels for this car. I thought this one was fairly unique in the styling, but tasteful and still has a little of the old school torque thrust kind of flare. As well as being reasonably priced.
Sent from iPhone
TGR96
el blanco nino
Well of course it's gonna rain now that you washed your car!
We could use some rain up here. No rain in the forecast for the near future. It does help keep the car clean, though.
What have I done to my Mustang today? Well, technically it was last week, but I ordered some gently used track pads for it from a fellow forum member, as well as some Cooltech seatbelt harness mounts. Trying to slowly make this thing more track ready/friendly.
Last edited:
Mach2burnout
05 Redfire GT
Well of course it's gonna rain now that you washed your car!
We could use some rain up here. No rain in the forecast for the near future. It does help keep the car clean, though.
What have I done to my Mustang today? Well, technically it was last week, but I ordered some gently used track pads for it from a fellow forum member, as well as some Cooltech seatbelt harness mounts. Trying to slowly make this thing more track ready/friendly.
We have some we can send you, but beware we've gotten a measurable amount of rain almost every day for the last 2 months. So be careful what you wish for.
Sent from iPhone
TGR96
el blanco nino
^^^ oh yeah I know you guys have been hammered. I wish we could get a little bit of what you guys have been getting down there over the past several weeks, just not ALL of it!
LAStang1234
----------DSL----------
Waxing it on this rainy day. I'm on leave and have no idea what to do with myself lol.
Sent from my SAMSUNG-SM-G890A using Tapatalk
Sent from my SAMSUNG-SM-G890A using Tapatalk
I swapped out the factory driveshaft for a shaft from a friend's '12 Roush
Mine had developed a noise in the rear section:
His was nice and solid:
The swap eliminated a clunk I was getting when putting a load on the driveline.
Noise gone, the car actually feels more eager to take off.
Can't wait to drive it again!!
.
Mine had developed a noise in the rear section:
His was nice and solid:
The swap eliminated a clunk I was getting when putting a load on the driveline.
Noise gone, the car actually feels more eager to take off.
Can't wait to drive it again!!
.
LAStang1234
----------DSL----------
Haha you would bring that up! I just don't know what color, I have a habit of touching the walls with sometimes greasy hands.
Sent from my SAMSUNG-SM-G890A using Tapatalk
Similar threads
Support us!
Support Us - Become A Supporting Member Today!
Click Here For Details
Sponsor Links
