07 Aluminator build

explict

Heavy Metal
S197 Team Member
Joined
Dec 6, 2008
Posts
597
Reaction score
6
Location
Fort McMurray Alberta
Big negative on the today start up. I am pretty sure I was sent the 1/2 inch drop K-member.
The steering shaft WILL NOT clear the header. I raised the motor 3/8'' and wedged the motor to the passanger side as much as possible, no go. Tomorrow I will try to raise the motor more if possible and or put a dent in the header.
 

explict

Heavy Metal
S197 Team Member
Joined
Dec 6, 2008
Posts
597
Reaction score
6
Location
Fort McMurray Alberta
Okay nevermind on that. People working late in the shop. I took two hammers, used one as a punch and the other as a hammer and put a small dent in the header. Shaft clears now.
 

explict

Heavy Metal
S197 Team Member
Joined
Dec 6, 2008
Posts
597
Reaction score
6
Location
Fort McMurray Alberta
It's alive!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

But it does not idle....I can hold the throttle and it will stay at a certain rpm but it does not stay idling. Sounds good when I hold it at like 2krpm. I'm going to check into it tomorrow.

Do you guys think I need a tune for it to idle because of the BBR Stage 2 cams?
 

DirtyDogOfTheDesert

Senior Member
S197 Team Member
Joined
Apr 18, 2007
Posts
1,001
Reaction score
12
Location
Canada/Yemen
Absolutely YES. It will not idle very well if at all on a stockish tune with those cams. Talk to Eric about writing you a quick base tune for them.

Just wait till you hear it idle with those cams... you're going to love it!
 
Last edited:

stauff

Junior Member
Joined
Sep 20, 2009
Posts
4
Reaction score
0
Are you sure it's the camera making it look dirty...? I think it looks dirty because everything is covered in dirt.

Clearly the camera is making this spotless car look dirty :roflmao:

DSCN0054.jpg


ps. there is fabric protecting the roof from getting scratched
 
Last edited:

explict

Heavy Metal
S197 Team Member
Joined
Dec 6, 2008
Posts
597
Reaction score
6
Location
Fort McMurray Alberta
Haha. Ya man.. car is really dirty from the tow down to the shop. (not same tow as in my sig)

Another problem I ran into last night. The rear passenger injector was leaking, it was because the bung ( I guess) was bent where the injector plugs in. So we bent it back into shape and the leak stopped 100%. I think it was just a bad seal with the o-ring.
going to call Eric this morning. See what he can do.
 

BruceH

BBB Big Bore Boss 322
Joined
Sep 13, 2009
Posts
13,801
Reaction score
14
Location
Pacific Northwest
Have you double checked all your vacuum lines? My car exhibited a similar condition once whent the brake booster line had popped off during a clutch install.
 

stkjock

---- Madmin ----
Staff member
Administrator
Super Moderator
S197 Team Member
Joined
Jul 10, 2007
Posts
40,260
Reaction score
3,171
Location
Long Island NY
clean that poor thing!

sounds good man...congrats on the start up
 

explict

Heavy Metal
S197 Team Member
Joined
Dec 6, 2008
Posts
597
Reaction score
6
Location
Fort McMurray Alberta
Ya once the snow and mud and slush clear up I am going to give it a realllly good spit shine. Probably wont even drive it for the next week...
I can't wait until I get a dyno tune!
 

stauff

Junior Member
Joined
Sep 20, 2009
Posts
4
Reaction score
0
This is what we are dealing with right now, winter is still in full force here. We cant even back Alex's car out of the shop now. Picture was taken less than an hour ago.

PS No one washes their cars cause they get dirty in hours.
DSCN1136.jpg
 

Vapour Trails

The Renaissance Man
Joined
Sep 17, 2008
Posts
2,773
Reaction score
40
Location
Winnipeg, MB, Canada
This is what we are dealing with right now, winter is still in full force here. We cant even back Alex's car out of the shop now. Picture was taken less than an hour ago.

PS No one washes their cars cause they get dirty in hours.
DSCN1136.jpg

That's rough, all the snow in Winnipeg was gone a week ago. We had an unusually short winter.
 

explict

Heavy Metal
S197 Team Member
Joined
Dec 6, 2008
Posts
597
Reaction score
6
Location
Fort McMurray Alberta
So I have a dyno time set and things on order are:
63# injectors.



Haha should there be anything else I should get?
Maybe a larger pulley from Steeda if I want more than the "11-13psi" pulley gives me? Should I get a larger throttle body? Hmm....trying to think of other things..
 

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Sponsor Links

Banner image
Back
Top